l9HP DECprint Supervisor (DCPS) for OpenVMSR

HP DECprint Supervisor (DCPS) for OpenVMS
User's Guide

z d f

"
X $ SET ENTRY nnn /RELEASE /NOCHECKPOINT queue-name

6In the command line, supply the following information:
nnn - The print job entry number in the queue
queue-name ! The name of the print queue

GThe print job will be reprinted from the beginning. Use the PAGE_LIMIT Dparameter if you want to print only the pages that were not printed before the paper jam occurred.

?PARSYNERR, Syntax error in the PARAMETERS qualifier at or near string
=Explanation: There is a syntax error in the H/PARAMETERS qualifier of the PRINT command. The error was located at or #near the string parameter.
EUser Action: Check the syntax of the parameters you <entered. Resubmit the print request with the correct syntax.

APPSGTNUP, Pages per sheet > Number_Up. Pages per sheet set to Number_Up
HExplanation: You included both a layup definition file Band the NUMBER_UP parameter in your print job. However, the layup Gdefinition file requests that the number of pages printed per sheet be ?greater than the number specified with the NUMBER_UP parameter.
DUser Action: No action is required if you want the Enumber of pages per sheet to equal the number you specified with the HNUMBER_UP parameter. If you want the number of pages per sheet to equal Athe number given in the layup definition file, reissue the PRINT @command specifying a larger number with the NUMBER_UP parameter.

PRESET, resetting printer
AExplanation: The printer controller detected an Einternal error. It executes the power-up sequence, which effectively 2resets the printer and the PostScript interpreter.
9User Action: No user action is required.

%PRHDWERR, Print Engine hardware error
GExplanation: There is a hardware error in the printer.
8User Action: Call HP Customer Services.

8PRINTERSTALLED, Printer printer-name is stalled
DExplanation: You usually see this message when the Hprinter is out of paper. Sometimes PostScript commands that take a long #time to execute cause this message.
GUser Action: Check for previous printer messages that @may indicate the reason for the stalled condition. Refer to the iSystem Manager's GuideSystem Manager's Guide for more information about stalled queues.

+PRUNKERR, Print Engine unknown error status
GExplanation: There is a hardware error in the printer.
GUser Action: Refer to the printer operator's guide or call HP Customer Services.

PRWRDWERR, printer timed out
@Explanation: The print engine reports no error Econdition, but it is not yet ready to print after correcting a print &engine error. This state is temporary.
9User Action: No user action is required.

8PSTERM, Unexpected termination of PostScript interpreter
EExplanation: The PostScript interpreter has a fatal error.
EUser Action: Report this problem to the HP Customer Support Center.

EPUNCHNOSUP, Punching feature not supported for printer-name printer
DExplanation: The printer to which you are printing 6does not have a DCPS-supported punch option installed.
GUser Action: Print to a printer with a DCPS-supported Gpunch option or do not specify the PUNCH parameter on the command line.

%PWRCYCL, The printer power was cycled
FExplanation: This is an informational message. Power *to the printer was turned off and then on.
#User Action: None.

<PWRFAIL, The printer power was cycled while a job was active
FExplanation: Power to the printer was turned off and !then on while a job was printing.
FUser Action: Check your print job to see if you need to resubmit it for printing.

FRANGECHK, rangecheck: Argument out of bounds --- offending command is string
BExplanation: The PostScript interpreter sensed a Arange-check error while trying to execute the PostScript command represented by string.
GUser Action: If this error occurs during the printing Eof a file with a data type other than PostScript, an error exists in Ethe translation process. If the translator is supplied by HP, report /this problem to the HP Customer Support Center.

EIf the error occurs during the printing of a PostScript file, either Ethe PostScript file or the application that generated the PostScript Gfile is in error. If the application is supplied by HP, contact the HP 4Customer Support Center and submit a problem report.

6REQMANFEED, Request manual feed of media-size
DExplanation: The printer changed input trays. This @message is displayed when you specify INPUT_TRAY=MANUAL_FEED or GINPUT_TRAY=ENVELOPE_FEEDER. The job separation pages have been printed Afrom the printer's default input tray and the file data is to be <printed on paper from the manual feed or envelope feed tray.
GUser Action: This message is informational, prompting =you to begin feeding the media into the requested input tray.

HREQMODNOTFOUND, Required device control module module-name not found
@Explanation: A required device control module, BLPS$$module-name, located in the standard device control (library, DCPS$DEVCTL.TLB, was not found.
DUser Action: Check to see that the standard device Hcontrol library, DCPS$DEVCTL.TLB, is listed in your library search list 2in the DCPS$STARTUP.COM file. Check the following:

Make sure the SYS$LIBRARY directory contains the DCPS$DEVCTL.TLB file.E
Make sure no previous versions of the DCPS$DEVCTL.TLB file are , stored in the SYS$SPECIFIC directory tree.J
Use the LIBRARY /LIST SYS$LIBRARY:DCPS$DEVCTL.TLB command to ensure @ that the indicated module-name is among those listed.

GIf the above conditions are not met, reinstall the DECprint Supervisor >software. If this problem persists, call HP Customer Services.

3SETUPFILE, running setup file created date
HExplanation: The creation date of the setup file being 0used by the DCPS startup procedure is displayed.
BUser Action: None. This message is informational.

(SETUPMODE, startup running in setup mode
GExplanation: The DCPS startup procedure is running in setup mode.
BUser Action: None. This message is informational.

:SETUPNOTFOUND, Setup module module-name not found
GExplanation: The setup module you requested cannot be $found in the device control library.
FUser Action: Make sure the setup module is stored in Bthe device control library search list. Check the spelling of the +module name and resubmit the print request.

:SETUPREADERR, Setup module module-name read error
GExplanation: The setup module you requested cannot be read.
EUser Action: Check to make sure the setup module is Gproperly stored in the device control library, and that the library is defined in the search list.

;SIZNOTAVL, No paper-size size medium is loaded in printer-name
BExplanation: The paper size you requested is not 8loaded in the printer associated with the print request.
BUser Action: Choose one of the following actions:

Load the desired paper in the specified input tray.C
Reenter the PRINT command, specifying the paper size that is - already loaded in the requested input tray.I
Reenter the PRINT command, specifying the input tray that contains the paper size you require.I
Reenter the PRINT command, specifying either the input tray or the paper size, but not both.

9SIZNOTRAY, paper-size size medium is not in the 0tray-name tray in printer-name
BExplanation: The paper size you requested is not +loaded in the input tray that you requested
6User Action: Do one of the following:

Load the desired paper in the specified input tray.C
Reenter the PRINT command, specifying the paper size that is - already loaded in the requested input tray.I
Reenter the PRINT command, specifying the input tray that contains the paper size you require.I
Reenter the PRINT command, specifying either the input tray or the paper size, but not both.

?SIZNOTSUP, paper-size size medium is not supported by printer-name
BExplanation: You requested a paper size that the printer does not support.
HUser Action: Resubmit your job and request a supported paper size.

9SPOOLBADDEVICE, error in DCPS$SPOOL_DIRECTORY device name
DExplanation: The logical name DCPS$SPOOL_DIRECTORY 2points to a directory on a device that is invalid.
<User Action: Correct the definition of the "DCPS$SPOOL_DIRECTORY logical name.

5SPOOLBADDIR, DCPS$SPOOL_DIRECTORY directory not found
DExplanation: The logical name DCPS$SPOOL_DIRECTORY #points to a non-existant directory.
HUser Action: Redefine the DCPS$SPOOL_DIRECTORY logical 2name so that it refers to a directory that exists.

=SPOOLERROR, error creating spool file in DCPS$SPOOL_DIRECTORY
BExplanation: A temporary spool file could not be Acreated in the directory referred to by the DCPS$SPOOL_DIRECTORY logical name.
FUser Action: Determine the cause of the problem with the directory.

)SPOOLFILENOOPEN, error opening spool file
GExplanation: The temporary spool file created earlier Ein the DCPS print job could not be opened for sending to the printer.
GUser Action: Determine why the file is not accessible Gor has been deleted after it was created but before it was sent to the printer.

>SPOOLNOLOGICAL, logical name DCPS$SPOOL_DIRECTORY is undefined
BExplanation: The logical name that specifies the Flocation of the spool directory, DCPS$SPOOL_DIRECTORY, is not defined.
6User Action: Define the logical name FDCPS$SPOOL_DIRECTORY to point to a directory that can be used by DCPS to store temporary spool files.

:SPOOLNOPRIV, no privilege to write to DCPS$SPOOL_DIRECTORY
FExplanation: DCPS could not create a temporary spool Bfile in the DCPS$SPOOL_DIRECTORY directory because of a privilege violation.
EUser Action: Make sure the directory referred to by Dthe logical name DCPS$SPOOL_DIRECTORY is protected so that the DCPS 1print symbiont can create files in the directory.

9SPOOLNOWRITE, DCPS$SPOOL_DIRECTORY device is write-locked
6Explanation: The device on which the :DCPS$SPOOL_DIRECTORY directory is located is write-locked.
HUser Action: Enable the device for writing or redefine &the DCPS$SPOOL_DIRECTORY logical name.

:STARTING, DECprint Supervisor version starting...
FExplanation: The DCPS startup procedure displays the ;current version and the fact that it is starting execution.
BUser Action: None. This message is informational.

HSTKOFLO, stackoverflow: Operand stack overflow --- offending command is string
HExplanation: The PostScript interpreter sensed a stack Boverflow condition while trying to execute the PostScript command represented by string.
GUser Action: If this error occurs during the printing Eof a file with a data type other than PostScript, an error exists in Ethe translation process. If the translator is supplied by HP, report /this problem to the HP Customer Support Center.

GSTKUFLO, stackunderflow: Operand stack underflow --- offending command is string
EExplanation: The PostScript interpreter detected an error in the file.
GUser Action: If this error occurs during the printing Eof a file with a data type other than PostScript, an error exists in Ethe translation process. If the translator is supplied by HP, report /this problem to the HP Customer Support Center.

CSTPNOSUP, Stapling feature not supported for product_name printer.
DExplanation: The printer does not support stapling.
DUser Action: Print to a printer that has a stapler installed.

;STPOUTTRAY, Selected output tray does not support stapling.
FExplanation: The output tray you specified cannot be used for stapling.
CUser Action: Specify an output tray that supports (stapling with the OUTPUT_TRAY parameter.

FSTPPOSNOSUP, Stapling position not supported for orientation and feed direction.
HExplanation: The printer cannot put a staple where you have requested.
AUser Action: Load the paper in a different feed Hdirection, if supported for that paper size, or choose a different page orientation.

HSTPSIZENOSUP, Stapling not supported for sheet_size size paper and feed direction.
AExplanation: The printer cannot staple your job Hbecause the paper size and/or paper feed direction is not supported for stapling.
AUser Action: Load the paper in a different feed ,direction, if supported for that paper size.

ASYNERR, syntaxerror: Input ended in string or procedure body --- $offending command is string
BExplanation: The PostScript interpreter sensed a Hsyntax error while trying to execute the PostScript command represented by string.
GUser Action: If this error occurs during the printing Hof a file with a data type other than PostScript, it indicates an error Hin the translation process. If the translator is supplied by HP, report /this problem to the HP Customer Support Center.

;SYNTAX_INCOMPLETE, Syntax incomplete at line n in "DCPS$FILE_EXTENSION_DATA_TYPE file
5Explanation: The syntax of the file @SYS$LIBRARY:DCPS$FILE_EXTENSION_DATA_TYPE.DAT[_DEFAULT] was not Dexpected. There will be no attempt to match file extensions to data types.
DUser Action: The system manager should correct the Hproblem in the file. The queue must be stopped (STOP /QUEUE /RESET) and 1started (START /QUEUE) for a new file to be read.

'TCPPORTINVALID, invalid TCP port number
HExplanation: The port number you specified is invalid. HSome types of network connections (for example, IP_RawTCP) require that Fyou specify the number of a TCP port on the printer that supports the associated protocol.
EUser Action: Verify that you specified a valid port @number. If no port number is specified, a value of 9100 is used.

*TCPPORTPRESENT, no TCP port number allowed
GExplanation: You specified a TCP port number for your Eprinter, but none is allowed. Some types of network connections (for Gexample, IP_CPAP) do not require or allow you to specify the number of a TCP port on the printer.
AUser Action: Verify that you have specified the Gdesired type of network connection. If so, remove the port number from !the queue's device specification.

$TIMOUT, timeout: Time limit exceeded
GExplanation: A PostScript program executed beyond the ?time limit set by the system manager. This can be caused by an Cunusually complex page definition or by an error in the PostScript 5application program that results in an infinite loop.
DUser Action: If the error is a result of a complex Cpage definition, ask the system manager to change the value of the printer timeout limit.

GIf this error is the result of an infinite loop that occurs during the Dprinting of a file with a data type other than PostScript, an error Hexists in the translation process. If the translator is supplied by HP, 6report this problem to the HP Customer Support Center.

FIf the error is the result of an infinite loop that occurs during the Aprinting of a PostScript file, either the PostScript file or the Capplication that generated the PostScript file is in error. If the Fapplication is supplied by HP, contact the HP Customer Support Center and submit a problem report.

.TNREND, Print Engine toner supply is exhausted
:Explanation: The printer is out of toner.
GUser Action: Replace the toner cartridge and cleaning Fpad. Refer to the instructions in the toner replacement kit or in the .LN03R ScriptPrinter Operator's Guide.

)TONEROFL, Toner collection container full
EExplanation: The toner collection container is full.
DUser Action: Following the directions in the toner Fkit, remove the full toner container bottle and replace it with a new bottle.

2TRANSJAM, Print engine transport section is jammed
BExplanation: Your printer has a paper jam in the transport section.
HUser Action: Clear the paper jam at the printer. Next, Eissue the following DCL command to release and restart the print job:

"
X $ SET ENTRY nnn /RELEASE /NOCHECKPOINT queue-name

6In the command line, supply the following information:
nnn - The print job entry number in the queue
queue-name ! The name of the print queue

GThe print job will be reprinted from the beginning. Use the PAGE_LIMIT Dparameter if you want to print only the pages that were not printed before the paper jam occurred.

4TRANSPORTBAD, invalid transport - transport
FExplanation: You have specified an invalid transport when starting a DCPS queue.
HUser Action: Review the possible network transports in ZHP OpenVMS System Management Utilities Reference Manual and specify a valid one.

=TRANSPORTNOTSUP, transport not supported - transport
EExplanation: You have specified a transport that is Enot supported on your system architecture when starting a DCPS queue.
HUser Action: Review the possible network transports in |the HP OpenVMS System Management Utilities Reference Manual and specify a valid one for your system. For example, 4AppleTalk queues cannot be started on an I64 system.

TRANSPORTREQ, transport required
FExplanation: You have not specified a transport when starting a DCPS queue.
HUser Action: Review the possible network transports in ^the HP OpenVMS System Management Utilities Reference Manual and specify a valid one.

/TRAYEMP, Print Engine paper input tray is empty
<Explanation: The paper input tray is empty.
@User Action: Add paper to the input paper tray.

#TRAYJAM, Input paper tray is jammed
HExplanation: Your printer's input paper tray is jammed.
HUser Action: Clear the paper jam at the printer. Next, Eissue the following DCL command to release and restart the print job:

"
X $ SET ENTRY nnn /RELEASE /NOCHECKPOINT queue-name

6In the command line, supply the following information:
nnn - The print job entry number in the queue
queue-name ! The name of the print queue

GThe print job will be reprinted from the beginning. Use the PAGE_LIMIT Cparameter to print only the pages that were not printed before the paper jam occurred.

HTRAYSUBST, Output will be delivered to the output-tray tray on printer-name
4Explanation: Informational message.
#User Action: None.

BTRNFAIL, Translation from data-type to PostScript failed.
HExplanation: The translator from data-type to EPostScript has generated an error. The translator software cannot be used.
EUser Action: Report this problem to the HP Customer Support Center.

ETRNNOTFND, Translator from data-type to PostScript not found
NExplanation: The DECprint Supervisor software could not find Fthe translator from data-type to PostScript in the SYS$SHARE directory.
AUser Action: The data type you specified in the DDATA_TYPE parameter or that is defined as the queue default must be 3either supplied by HP or a user-written translator H(TRN$data-type_PS.EXE in the SYS$SHARE directory). Correct the )condition and resubmit the print request.

?TRYNOTRDY, tray-name tray on printer-name is current-tray-name
FExplanation: The input tray is not loaded with paper.
AUser Action: Prepare the printer input tray and resubmit the print job.

ATUMBNOSUP, printer-name does not support tumble printing
BExplanation: The printer does not support tumble printing.
CUser Action: Resubmit your job without requesting Dtumble printing. Or resubmit the print job with /QUEUE specifying a &printer that supports tumble printing.

CTYPCHK, typecheck: Argument of wrong type --- offending command is string
EExplanation: The PostScript interpreter sensed this Hsyntax error while trying to execute the PostScript command represented by string.
GUser Action: If this error occurs during the printing Eof a file with a data type other than PostScript, an error exists in Ethe translation process. If the translator is supplied by HP, report /this problem to the HP Customer Support Center.

:UNDEF, undefined: Name not known --- offending command is string
EExplanation: The PostScript interpreter sensed this Hsyntax error while trying to execute the PostScript command represented by string.
GUser Action: If this error occurs during the printing Eof a file with a data type other than PostScript, an error exists in Ethe translation process. If the translator is supplied by HP, report /this problem to the HP Customer Support Center.

FUNDEFRES, undefinedresult: Number overflow or underflow --- offending command is string
CExplanation: The PostScript interpreter sensed an Derror while trying to execute the PostScript command represented by string.
GUser Action: If this error occurs during the printing Eof a file with a data type other than PostScript, an error exists in Ethe translation process. If the translator is supplied by HP, report /this problem to the HP Customer Support Center.

FUNDFILNAM, undefinedfilename: File not found --- offending command is string
CExplanation: The PostScript interpreter sensed an Derror while trying to execute the PostScript command represented by string.
GUser Action: If this error occurs during the printing Eof a file with a data type other than PostScript, an error exists in Ethe translation process. If the translator is supplied by HP, report /this problem to the HP Customer Support Center.

BUNKDATATYPE, Unknown data type: string or translator not available
HExplanation: The DECprint Supervisor software does not Erecognize the DATA_TYPE parameter specified in the PRINT command, or 7the indicated translator could not be found or started.
CUser Action: Check the PRINT command, correct the ADATA_TYPE parameter, and resubmit your request. If the DATA_TYPE Bparameter is valid, have your system manager check that the TRN$* _translator files listed in the Release NotesRelease Notes are in the correct Elocation on your system and have WORLD:RE protection. Also have your Bsystem manager check process-related quotas and resources for the ASYSTEM account, if your system is using multistreamed DCPS print symbionts.

:UNKFILTAG, File tag is unknown. Tag value: number
7Explanation: The file contains a DDIF Dstored_semantics tag that is not recognized by the DECprint Supervisor software.
GUser Action: You cannot print this type of file using DECprint Supervisor software.

BUNKNOWN_DEFTRANS, data-type is not expected as a Default Translator, but it will be used
AExplanation: The data type given by the logical GDCPS$queuename_DEFAULT_TRANSLATOR as the default data type is Dnot one that the DECprint Supervisor provides a translator for. The KDECprint Supervisor software will attempt to find and use a translator for this data type.
FUser Action: This message is informational only; the Eprint job is printed. The system manager should ensure that the data Ftype is actually one that is desired. If so, ensure that a translator Hexists in the SYS$SHARE directory for such a data type. If not, correct Bthe specification of the logical. The queue must be stopped (STOP G/QUEUE /RESET) and started (START /QUEUE) for a new definition to take effect.

GUNKNOWN_PROLOG, Unknown prolog---version version-number, name prolog-name
DExplanation: Dialog between the print symbiont and $printer produced unexpected results.
GUser Action: If you continue to receive this message, call HP Customer Services.

AUNMATCH, unmatchedmark: Expected mark not on stack --- offending command is string
CExplanation: The PostScript interpreter sensed an Derror while trying to execute the PostScript command represented by string.
GUser Action: If this error occurs during the printing Eof a file with a data type other than PostScript, an error exists in Ethe translation process. If the translator is supplied by HP, report /this problem to the HP Customer Support Center.

AUNRECOGNIZED, Product name product-name not recognized; assuming Unrecognized
GExplanation: The printer model mentioned is not an HP Gprinter and not one supported by DCPS. A set of commands known to work Fon other models will be used. Not all DCPS features will be supported.
DUser Action: None. This message states the mode in which the printer will be run.

FUNREGIST, unregistered: PostScript has encountered a system error --- $offending command is string
CExplanation: The PostScript interpreter sensed an Derror while trying to execute the PostScript command represented by string.
GUser Action: If this error occurs during the printing Eof a file with a data type other than PostScript, an error exists in Ethe translation process. If the translator is supplied by HP, report /this problem to the HP Customer Support Center.

z a d f

Contents

Index

nnn	- The print job entry number in the queue
queue-name	! The name of the print queue

HP DECprint Supervisor (DCPS) for OpenVMSUser's Guide

HP DECprint Supervisor (DCPS) for OpenVMS
User's Guide