CONTENTS Title Page Copyright Page Preface 1 Preparing to Install the KAV30 1.1 Physical and Environmental Requirements 1.2 Unpacking Instructions 1.3 KAV30 Orientation 2 Installing the KAV30 2.1 Beginning the Installation 2.2 Configuring the VMEbus Backplane 2.3 Configuring the VSB Backplane 2.4 Configuring the KAV30 2.4.1 Jumper Posts 2.4.2 DIP Switches 2.4.3 Rotary Switch 2.5 Inserting the KAV30 into a VMEbus Crate 2.6 Connecting Devices to the Serial Line Ports 2.7 Connecting Devices to the AUI Port 2.8 Connecting Devices to the SCSI Port 2.9 Finishing the Installation 3 Testing the KAV30 3.1 Diagnostic Tests 3.2 Diagnostic Halt on Fatal Error 3.2.1 Differences between KAV30 Revision Levels A and B 3.3 Utilities 4 KAV30 Hardware 4.1 Overview of the KAV30 Hardware 4.2 Status Display 4.3 Reset/Halt Switch 5 Operating the KAV30 5.1 Console Program 5.1.1 Running the Console Program 5.1.2 Console Program Commands 5.1.3 Console Program Messages 5.2 Booting the KAV30 5.3 Using Utilities 5.4 Testing the KAV30 Auxiliary Power Supply 5.5 Troubleshooting the SCSI Bus 6 Replacing the KAV30 User ROM 6.1 Overview of the KAV30 User ROM 6.2 Removing the KAV30 from a VMEbus Crate 6.3 Replacing the EPROMs 6.4 Programming the EPROMs A KAV30 Hardware Specifications A.1 Temperature and Humidity Specifications A.2 Power Supply Specifications A.3 Bus Load Specifications A.4 Timing Specifications B Diagnostic Tests C VAXELN Pascal Program D KAV30 Port Connectors D.1 Console and Auxiliary Port Connectors D.2 AUI Port Connector D.3 SCSI Port Connector Glossary application program . . . DECconnect DELNI . . . FIFO FIFO buffer . . . MMP module . . . SGM slot . . . 802.3 FIGURES 1-1 KAV30 Orientation 1-2 KAV30 Parts 2-1 KAV30 Jumper Post Locations 2-2 KAV30 DIP Switch Orientation 2-3 Inserting the KAV30 into a VMEbus Crate 4-1 KAV30 Hardware Block Diagram 6-1 Replacing the KAV30 EPROMs D-1 Serial Line Port Connector Layout D-2 SCSI Port Connector Layout TABLES 1-1 KAV30 Hardware Kit Items 1-2 KAV30 Module Options 1-3 Additional KAV30 Hardware Installation Items 2-1 Settings for User ROM Size Jumper Posts 2-2 Settings for Auxiliary Power Source Jumpers 2-3 Settings for Boot Source Switches 2-4 Default Console and Auxiliary Port Settings 3-1 Diagnostic Test 3 Sub-Test Codes 5-1 Boot Source Device Names 5-2 KAV30 Utilities 5-3 Troubleshooting the SCSI Bus 6-1 User ROM Sizes A-1 Temperature and Humidity Specifications A-2 Maximum Power Supply Specifications A-3 KAV30 Bus Load Specifications A-4 System RAM Access Timing-Specifications B-1 KAV30 Diagnostic Tests D-1 Serial Line Port Connector Pin Specification D-2 AUI Port Connector Pin Specification D-3 SCSI Port Connector Pin Specification