 















          MIRA MicroVAX Software Installation
          Guide


          Order Number: AA-KK07C-TN
          Software Version:             MIRA V2.2
























          digital equipment france, annecy

 




          ________________________
          September 1990
          __________
          The information in this document is subject to change
          without notice and should not be construed as a
          commitment by Digital Equipment Corporation. Digital
          Equipment Corporation assumes no responsibility for
          any errors that may appear in this document.

          The software described in this document is furnished
          under a license and may be used or copied only in
          accordance with the terms of such license.
          No responsibility is assumed for the use or
          reliability of software on equipment that is not
          supplied by Digital Equipment Corporation or its
          affiliated companies.

          Restricted Rights: Use, duplication, or disclosure
          by the U.S. Government is subject to restrictions as
          set forth in subparagraph (c)(1)(ii) of the Rights in
          Technical Data and Computer Software clause at DFARS
          252.227-7013.
          __________
          Copyright 1990 by Digital Equipment France

          All Rights Reserved.
          __________

          The following are trademarks of Digital Equipment
          Corporation:
          DEC            DIBOL          UNIBUS
          DEC/CMS        EduSystem      VAX
          DEC/MMS        IAS            VAXcluster
          DECnet         MASSBUS        VMS
          DECsystem-10   PDP            VT
          DECSYSTEM-20   PDT
          DECUS          RSTS
          DECwriter      RSX            DIGITAL


          This document was prepared using VAX DOCUMENT, Version
          1.1

 


 






          _______________________________________________________

   1       Introduction to MicroVAX/VMS MIRA Software
          Installation



          This guide tells you how to install the MicroVAX/VMS
          MIRA software on your MIRA system. Before you install
          this software, the VMS operating system (V5.3 or
          later) must be installed.
          The MIRA installation takes about 15 minutes. Begin
          by following the instructions in this guide. After
          you have followed the preliminary instructions in this
          guide, you must follow instructions from your terminal
          to complete the installation.

          The MicroVAX/VMS MIRA software is distributed on a
          single TK50 cartridge or one tape. This cartridge or
          tape contains all the required components to properly
          install the MIRA software.
          The MIRA software should be installed on both MIRA
          systems. It requires 3800 blocks of disk space during
          installation, but when the installation is complete it
          only occupies 800 blocks.

          For more information about the MIRA software, see the
          following manuals:
          -  MIRA MicroVAX User's guide (Order Number: AA-KK07D-
             TN)

          -  MIRA Release Notes (in the file
             SYS$HELP:MRA022.RELEASE_NOTES)

          The steps to install the VMS software are listed
          below:
          1  Boot the system.

          2  Run the VMSINSTAL command file.


                                                              1-1

 

          Introduction to MicroVAX/VMS MIRA Software Installation




          3  Log out after the installation has completed.

          Examples of a complete installation and verification
          procedure, and the list of the files provided by the
          installation procedure are given in the appendices to
          this manual.


          Convention: The symbol <RET> means that you must press
          the RETURN key.































          1-2

 






          _______________________________________________________

   2       Installing the MIRA Software



          __________________________________________________________________

   2.1     Invoking the Installation Command File
          Log into the SYSTEM account and execute the command
          file VMSINSTAL in the directory SYS$UPDATE with the
          following command:


                           @SYS$UPDATE:VMSINSTAL
          The system asks you if your system disk is backed up,
          and asks for the device where the cartridge or tape
          will be mounted.

          The system reminds you to put the cartridge or tape in
          the drive and you confirm that the medium is in place
          by entering "Y".
          The system asks you for the product name. Then you
          type MRA.

          With VMS V5.3, after all the MIRA software has been
          copied to the disk, the system asks you whether
          a licence has been registered or not. You should
          confirm this by entering "Y". If you enter "N",
          then the installation procedure is aborted and the
          appropriate licence should be registered before re-
          installing. Refer to Chapter 6 for details of the
          licence registration.
          The system asks you whether MIRA-Ada interface is
          required or not. If you answer "Y" to this question
          (which is the default), VAX Ada must be already
          installed on your processor, otherwise the MIRA
          installation will fail.



                                                              2-1

 

          Installing the MIRA Software




          The system asks you whether you want to purge the
          files replaced by this installation. You should
          confirm by entering <RET>, otherwise type "N".
          __________________________________________________________________

   2.2     Verifying the Installation
          ___________________________
   2.2.1   * Do you want to run the IVP?
          This question is asked only if the MIRA-Ada procedure
          interface is not needed. It is recommended that you
          run the Installation Verification Procedure in all
          cases. It is compulsory if the MIRA-Ada procedure
          interface is installed.
          The Installation Verification Procedure checks:

          1  the MIRA Driver software
          2  the MIRA Operator Interface software

          3  the MIRA Application Interface software
          4  the MIRA-Ada Procedure Interface (if present).

          Note: The Installation Verification Procedure calls two
          command files:

              SYS$TEST:MRA$IVP.COM
              SYS$TEST:MRA$ADA_IVP.COM

           You can execute these files at any time as a
          confidence test. Only the first file should be
          executed if MIRA-Ada has not been installed.
          If a problem occurs during the IVP, you should compare
          two files located in the SYS$TEST directory. One of
          these files contains the intended (correct) results
          of a given test, and the other will contain the actual
          results obtained. Table 2-1 gives the names of these
          files for each IVP test that is run.





          2-2

 

                                     Installing the MIRA Software




          Table 2-1 IVP Test Result Files in SYS$TEST:
          _______________________________________________________
          IVP_Test____________Actual_Output_____Intended_Output__
          MIRA Driver         MRA$DRVOUTPUT.DAT MRA$DRVRESULT.DAT

          MIRA Operator       MRA$OIOUTPUT.DAT  MRA$OIRESULT.DAT
          Interface

          MIRA Application    MRA$AIOUTPUT.DAT  MRA$AIRESULT.DAT
          Interface
          _______________________________________________________

          __________________________________________________________________
   2.3     Post-installation Procedures
          Do not forget to log out, in order to delete all
          the logical names and global symbols created by the
          VMSINSTAL.COM command file.
























                                                              2-3

 






          _______________________________________________________

   3       System Configuration




          When the MIRA software installation is complete and
          the Installation Verification Procedure have been
          successfully executed, you should configure your
          system.
          This is done from the SYSTEM account, by executing the
          command file SYS$MANAGER:MRA$CONFIG.COM.

          __________________________________________________________________
   3.1     Questions about the Hardware
          ___________________________
   3.1.1   * CSR address of the MIRA device?
          The MIRA device address should be entered in octal
          notation. If the MIRA device address on your system is
          different from the standard one, enter the correct
          address in octal notation (enter only the octal
          digits, for example: 760400<RET> ), otherwise press
          <RET>.

          ___________________________
   3.1.2   * Interrupt vector of the MIRA device?

          The MIRA device interrupt vector, in the range 300-
          774, should be entered in octal notation. If the
          interrupt vector of the MIRA device on your system
          is different from the standard one, enter the correct
          vector address (only the octal digits, e.g. 310<RET>
          ), otherwise press <RET>. If you enter a value, the
          system checks that this value is in the range from
          300(8) to 774(8).





                                                              3-1

 

          System Configuration



          __________________________________________________________________
   3.2     Customising the MIRA Software

          The following questions concern local variations to
          the setup of the MIRA software.

          ___________________________
   3.2.1   * Is the Application Interface needed?

          Enter "N" if you do not need the Application
          Interface. Otherwise press <RET>.

          ___________________________
   3.2.2   * Directory name for the Switch Map file?
          The Switch-Map file will be placed in this directory.
          The default is SYS$MANAGER.

          ___________________________
   3.2.3   * Do you want to create this directory on your target
          system directory?

          The system asks you this question if you enter a
          directory which does not already exist on the disk.
          The system will create the directory, if requested.
          __________________________________________________________________
   3.3     Questions about the Application Interface

          The questions below are needed to generate the
          MRA$STARTUP.COM command file. The corresponding
          answers will be the qualifiers of the MIRA_CONTROL
          START command.

          ___________________________
   3.3.1   * Timer value to start MIRA?

          You should enter a value in seconds, in decimal or
          integer format. Your answer will be truncated to one
          place of decimals. The default answer is 5 seconds.
          Minimum value is 300 milliseconds (0.3 second).
          Maximum value is 27 seconds.


          3-2

 

                                             System Configuration



          ___________________________
   3.3.2   * Delay value to start MIRA?

          You should enter a value in seconds, in decimal or
          integer format. Your answer will be truncated to one
          place of decimals. The default answer is 20 seconds.
          Minimum value is 300 milliseconds (0.3 second).
          Maximum value is 27 seconds.

          ___________________________
   3.3.3   * Do you want the MIRA software to start with the
          ALARM enabled?
          The default answer corresponds to the command
          qualifier "/ALARM" for the MIRA_CONTROL START command.

          ___________________________

   3.3.4   * Do you want the MIRA software to start with the Flag
          file management enabled?
          The default answer corresponds to the command
          qualifier "/FLAGFILE" for the MIRA_CONTROL START
          command.

          ___________________________
   3.3.5   * Do you want the MIRA software to start with the
          standard Master/Standby mode of operation enabled?

          The default answer corresponds to the command
          qualifier
          "/RELEASELINES" for the MIRA_CONTROL START command.

          ___________________________
   3.3.6   * Maximum delay for line reconnexion attempts?
          This question is asked only if you have answered "N"
          to the previous question. You should enter a value
          in VMS Delta Time format (for example, ":30:00"
          would specify "thirty minutes". The default answer
          is 20 seconds. Minimum value is 1 second. There is no
          maximum value.



                                                              3-3

 

          System Configuration



          ___________________________
   3.3.7   * Do you want the MIRA software to start with
          automatic clocks synchronization?

          The default answer corresponds to the command
          qualifier
          "/NOCLOCKSYNCHRONIZATION" for the MIRA_CONTROL START
          command.

          ___________________________
   3.3.8   * Should clock synchronization be periodically
          rescheduled?
          This question is asked only if you have answered "Y"
          to the previous question.

          ___________________________

   3.3.9   * Clock synchronization reschedule interval?
          This question too is asked only if you have answered
          "Y" to the previous question. You should enter a value
          in VMS Delta Time format. The default answer is one
          day (24 hours). Minimum value is 1 minute. There is no
          maximum value.

          ___________________________
   3.3.10  * Application Interface Control process priority?

          You should enter a value in the range 0-15. The
          default priority is 15. In most cases, you do not
          need to modify this priority, in which case just press
          <RET>. If you supply a value that is different from
          the default value, this will have a serious impact on
          the behaviour of the MIRA system. You should only do
          this after having acquired an in-depth understanding
          of how the MIRA software runs. Refer to MIRA MicroVAX
          User's guide for more information.






          3-4

 

                                             System Configuration



          ___________________________
   3.3.11  * Is the MIRA-ADA procedure interface needed?

          If you answer "Y" to this question (this is the
          default), VAX Ada must be already installed on your
          processor. Otherwise, the MIRA installation will fail.
          __________________________________________________________________
   3.4     Mistakes when Answering the Questions
          ___________________________
   3.4.1   * Do you validate all your previous responses

          If you are satisfied with all your answers press
          <RET>. Otherwise enter "N". The system then asks you
          all the questions again.
          __________________________________________________________________
   3.5     Entering the Switch-Map File Content

          After building the MIRA software components and if the
          Application Interface is needed, you are asked for the
          Switch-Map File content. Refer to "MIRA User's guide"
          for the structure of this file.





















                                                              3-5

 






          _______________________________________________________

   4       The Elaborate-Switch-Map Utility




          This tool is provided to create or alter the Switch-
          Map file.
          __________________________________________________________________
   4.1     Components of the Elaborate-Switch-Map Utility

          It consists of:
          1  Two programs which reside on the directory
             SYS$SYSTEM

             o  MRA$SWITCHMAP_CREATE
                This program creates a new Switch-Map file.
             o  MRA$SWITCHMAP_MODIFY
                This program modifies an existing Switch-Map
                file.

          2  One command file which resides on the directory
             SYS$MANAGER
             o  MRA$SWITCHMAP.COM
                This command file asks you for the file
                specification of the Switch-Map to be created
                or modified. The default answer is the
                "Default Switch-Map" which is located in the
                directory defined during configuration (see
                Section 3.2.2). The system then attempts to find
                this file on the local computer. If the file is
                found, the system runs the MRA$SWITCHMAP_MODIFY
                program to modify the existing switch-map file;
                if not, the system runs the MRA$SWITCHMAP_CREATE
                program to create a new switch-map file.





                                                              4-1

 

          The Elaborate-Switch-Map Utility



          __________________________________________________________________
   4.2     Invoking the Elaborate-Switch-Map Utility

          To invoke the Elaborate-Switch-Map Utility, you
          must have the SYSPRV privilege. You can invoke this
          utility, whether the MIRA software is running or not,
          with the following command:

               $ @SYS$MANAGER:MRA$SWITCHMAP.COM [switch-map-filename]
          If you omit the switch-map-filename parameter, you
          will be asked to supply one. If you then just press
          <RET> , then the default value will be the "Default
          Switch-Map" if it is defined; there is no default when
          the "Default Switch-Map" is not defined.

          Note: You should always have the same Switch-Map file
          on both systems. To ensure this, you can either create
          it in the same way on each system, or create it on one
          system and copy it to the other system via DECnet (if
          available).

          __________________________________________________________________
   4.3     Specifying Logical Names for Management of Switch-Map
          File

          Four logical names handle the Switch-Map File:
          1  Switch-Map Directory
             The logical name MRA$SWITCHMAP_DIR refers to the
             directory, containing the switch-map file(s),
             defined during configuration.

          2  Default Switch-Map
             The logical name MRA$DEF_SWITCHMAP refers to the
             Switch-Map File MRA$SWITCHMAP.DAT defined during
             configuration.
          3  Working Switch-Map
             The logical name MRA$SWITCHMAP refers to the
             Switch-Map used by the Operator Interface and the
             Application Interface.



          4-2

 

                                 The Elaborate-Switch-Map Utility




             This logical name is created by the Operator
             Interface after a MIRA_CONTROL START command,
             according to the following rules:

             -  If START command contains a /SWITCHMAP
                qualifier, the "working Switch-Map" equates
                to that given by the /SWITCHMAP qualifier.
             -  If START command does not contain any /SWITCHMAP
                qualifier and if the "default Switch-Map" is
                defined, the "working Switch-Map" equates to the
                "default Switch-Map".

             -  if START command does not contain any /SWITCHMAP
                qualifier and if the "default Switch-Map" is
                not defined, the "working Switch-Map" equates to
                SYS$MANAGER:MRA$SWITCHMAP.DAT
                If you start MIRA with an unmodified
                MRA$STARTUP.COM command file, the "Working
                Switch-Map" equates to the "Default Switch-
                Map".

          4  Elaborate Switch-Map
             The logical name MRA$ELAB_SWITCHMAP refers to the
             Switch-Map used by the "Elaborate Switch-Map"
             utility. It only exists while MRA$SWITCHMAP.COM
             is executing.















                                                              4-3

 






          _______________________________________________________

   5       Installing in a Cluster Environment




          This software can be installed on a MIRA system
          belonging to a VAXcluster. The following should be
          noted:
          1  The installation procedure will put executable
             files, Switch-Map files and general command files
             in the common root directories.

          2  The installation procedure will put the Switch-Map
             file and MIRA specific procedures in the specific
             root directories.
          3  The MIRA system, once running, will put the flag
             file and the events log file in the specific root
             directories.

          It is recommended that the software installation
          procedure be run on each licensed MIRA MicroVAX in
          your cluster.

          However, you may greatly speed up this process by
          observing the following:
          1  If your MIRA system is the only MIRA system in your
             cluster, you can perform the installation once,
             on either MIRA MicroVAX. Then the specific MIRA
             startup procedures put into the specific [SYSMGR]
             directory (MRA$STARTUP.COM, MRA$MASTERSTARTUP.COM,
             MRA$STANDBY.COM and UTSTARTUP.COM) by the
             installation procedure, should be moved to the
             other specified [SYSMGR] directories. The systems
             will use the same hardware and startup parameters
             and the same Switch-Map file.




                                                              5-1

 

          Installing in a Cluster Environment




          2  If you have more than one MIRA system on your
             cluster, you can perform the installation only
             once, on either MIRA MicroVAX of any MIRA system of
             the cluster. In this case, however, you should
             carry out the following steps. It is assumed
             that the pairs of MIRA systems have not the same
             hardware configuration and will not be started with
             the same MIRA_CONTROL START parameters:

             i  The specific MIRA startup procedures,
                put into the specific [SYSMGR] directory
                (MRA$STARTUP.COM, MRA$MASTERSTARTUP.COM,
                MRA$STANDBYSTARTUP.COM and UTSTARTUP.COM) by
                the installation procedure, should be moved
                to the other specific [SYSMGR] directories and
                edited to reflect the hardware configuration of
                each pair of MIRA MicroVAX (UTSTARTUP.COM with
                correct MIRA logic CSR and Vector addresses)
                and the desired START command parameters
                (MRA$STARTUP.COM).
            ii  The Switch-Map files should be moved to
                their respective specific directories in
                each processor of each MIRA system and then
                modified as required on the appropriate MIRA
                MicroVAX computers using the cluster-wide
                MRA$SWITCHMAP.COM procedure. This will ensure
                that the right files are found for each MIRA
                processor in your cluster.

          Note: If your cluster is a Local Area VAXcluster with
          two system disks, at least one installation should be
          performed per disk.









          5-2

 






          _______________________________________________________

   6       Software Licensing




          Versions 5.0 and above of the VMS operating system
          include the Licence Management Facility (LMF). This is
          a software feature which prevents customers from using
          software for which they have not purchased a licence.
          Version 2.2 of MIRA incorporates an interface to LMF.
          This has the following repercussions:

          o  If you install MIRA V2.2 for use with VMS
             Version 5.0 or above, you will have to supply the
             appropriate key at installation time.
          o  If you install MIRA V2.2 for use with VMS Version
             4.x, and you subsequently update VMS to Version
             5.3 or above without supplying the MIRA key at
             VMS installation time, you will get an error when
             you execute the MIRA_CONTROL command-that is, you
             will not be able to execute commands at the MIRA>
             prompt.

















                                                              6-1

 






          _______________________________________________________

   7       Licence Registration Procedure




          On VMS V5.3, you should register your MIRA licence
          before install it. For this purpose, you should enter
          the following command:

                          @SYS$UPDATE:VMSLICENSE
          The systems asks you the characteristics of the MIRA
          Software to be registered. Use the PAK provided with
          the software to register the licence.


























                                                              7-1

 






          _______________________________________________________

   A       Example of VMS V5.0 Installation and Verification
          Process



          $@SYS$UPDATE:VMSINSTAL<CR>
           VAX/VMS Software Product Installation Procedure V5.3-0
          It is 14-SEP-1990 at 16:50.
          Enter a question mark (?) at any time for help.
          * Are you satisfied with the backup of your system disk [YES] ? <CR>
          * Where will the distribution volumes be mounted: $2$DIA3:[0,0] <CR>
          Enter the products to be processed from the first distribution volume set.
          * Products: MRA022<CR>
          * Enter installation options you wish to use (none): <CR>
          The following products will be processed:<CR>
            MRA V2.2
           Beginning installation of MRA V2.2 at 16:50

          %VMSINSTAL-I-RESTORE, Restoring product save set A ...
          %VMSINSTAL-I-
          RELMOVED, Product's release notes have been moved to SYS$HELP.
                  Product:      MIRA-SWITCH-CONTROL
                  Producer:     DEC
                  Version:      2.2
                  Release Date: 01-JUL-1990
          * Does this product have an authorization key registered and loaded? Y<CR>
                   Your MIRA driver is loaded.
            Until the system can be rebooted to activate the new driver,
            the Installation Verification Procedure (IVP) is not testing
            the newly installed driver.To properly test the new driver,
            please reboot the system and run the IVP.

            You should reboot your system when your installation is complete
            and run the Installation Verification Procedure with the following
            command : @SYS$TEST:MRA$IVP




                                                              A-1

 

          Example of VMS V5.0 Installation and Verification Process




          * Is MIRA-ADA interface needed (VAX-
          ADA must be already installed) [YES]? N<CR>
          * Do you want to purge files replaced by this installation [YES]? <CR>
          * Do you want to run the IVP after the installation [YES]? <CR>

            We have now to build the MIRA software components. This can take 10 to 20
            minutes, depending on your quotas. Please, wait ...

            The MRA$STOP.COM command file which stops the MIRA software is
            located on the SYS$MANAGER directory.
            If you want to stop the MIRA software at system shut-
          down, you have to add
            the invocation of this file in your SYS$MANAGER:SYSHUTDWN.COM command file.

            The MRA$STARTUP.COM command file which starts the MIRA software is
            generated by the MRA$CONFIG.COM procedure.
            If you want to start the MIRA software at system start-
          up,you have to add
            the invocation of this file in your SYS$MANAGER:SYSTARTUP_
          V5.COM
            Please ensure that you logout after the installation is complete
            in order that the products logicals are correctly defined.

            After this installation, please execute the MRA$CONFIG.COM procedure
            to ensure a correct configuration of your system. This procedure is
            located in the SYS$MANAGER directory.
          %VMSINSTAL-I-
          MOVEFILES, Files will now be moved to their target directories...

          * Beginning the MIRA Installation Verification Procedure.

            The MIRA V2.2 Driver Software has been tested successfully.

            The MIRA V2.2 Operator Interface Software has been tested successfully.

            The MIRA V2.2 Application Interface Software has been tested successfully.


            The MIRA V2.2 standard Installation Verification Procedure has been tested
            successfully

          A-2

 

        Example of VMS V5.0 Installation and Verification Process




          * The MIRA V2.2 installation has been installed successfully

           Installation of MRA V2.2 completed at 16:55
          Enter the products to be processed from the next distribution volume set.
          * Products: EXIT<CR>
           VMSINSTAL procedure done at 16:56<CR>



































                                                              A-3

 






          _______________________________________________________

   B       List of the files provided by MIRA installation




          The following files are provided by the Installation
          Procedure:
          _______________________________________________________
          Directory:_SYS$SYSTEM__________________________________

          UTDRIVER.EXE         MIRA Driver
          UTTESTER.EXE         Driver Tester for Installation
                               Verification Procedure

          MRA$OPERATOR.EXE     Operator Interface program

          MRA$CONTROL.EXE      Application Interface program

          MRA$TRIGGER.EXE      Trigger program

          MRA$DEMO.EXE         Application Interface Tester
                               for Installation Verification
                               Procedure

          MRA$SWITCHMAP_       Program to create a new Switch-
          CREATE               Map
          .EXE

          MRA$SWITCHMAP_       Program to modify an existing
          MODIFY               Switch-Map
          .EXE








                                                              B-1

 

          List of the files provided by MIRA installation



          _______________________________________________________
          Directory:_SYS$SYSTEM__________________________________


          MRA$SAMPADA.EXE      Application Interface Tester
                               written in Ada for Installation
                               Verification Procedure (if MIRA-
                               Ada procedure interface required)

          _______________________________________________________
          Directory:_SYS$MANAGER_________________________________

          UTSTARTUP.COM        Loads the driver
          MRA$STARTUP.COM      Starts the MIRA Application
                               Interface

          MRA$MASTERSTARTUP.COMInvoked each time the system
                               starts as MASTER

          MRA$STANDBYSTARTUP.COInvoked each time the system
                               starts as STANDBY

          MRA$STOP.COM         Stops the MIRA Application
                               Interface

          MRA$SWITCHMAP.COM    "Elaborate Switch-Map" command
                               file















          B-2

 

                  List of the files provided by MIRA installation



          _______________________________________________________
          Directory:_SYS$HELP____________________________________

          MRATESTHELP.HLB      Help Messages File for the Driver
                               Tester
          MRADEMOHELP.HLB      Help Messages File for the
                               Application Interface Tester

          MRAHELP.HLB          Help Messages File for the
                               Operator Interface


          _______________________________________________________
          Directory:_MRA$SWITCHMAP_DIR___________________________

          MRA$SWITCHMAP.DAT    Switch-Map File
          _______________________________________________________
          Directory:_SYS$MESSAGE_________________________________

          MRAMSG.EXE           MIRA Software Messages file






















                                                              B-3

 

          List of the files provided by MIRA installation



          _______________________________________________________
          Directory:_SYS$LIBRARY_________________________________

          UTDEF.BAS            Symbols and statuses used by the
                               MIRA Driver (for BASIC programs)
          UTDEF.FOR            Symbols and statuses used by
                               the MIRA Driver. (for FORTRAN
                               programs)

          UTDEF.H              Symbols and statuses used by the
                               MIRA Driver (for VAX-C programs)

          UTDEF.MAR            Symbols and statuses used by the
                               MIRA Driver. (for MACRO programs)

          UTDEF.PAS            Symbols and statuses used by
                               the MIRA Driver. (for Pascal
                               programs)
























          B-4

 

                  List of the files provided by MIRA installation



          _______________________________________________________
          Directory:_SYS$LIBRARY_________________________________

          UTDEF.PLI            Symbols and statuses used by the
                               MIRA Driver (for PL1 programs)

          UTDEF.R32            Symbols and statuses used by the
                               MIRA Driver (for BLISS programs)

          UT_SSDEF.OBJ         MIRA software module to be
                               linked with user applications.
                               It contains all the statuses
                               returned by the MIRA Driver.
                               (refer to MIRA User's guide
                               Manual)

          MRA$USER.OBJ         MIRA software module to be
                               linked with user applications.
                               It contains the code of the
                               functions MRACON, MRAENA, MRADIS
                               and MRASWA.





















                                                              B-5

 

          List of the files provided by MIRA installation



          _______________________________________________________
          Directory:_SYS$LIBRARY_________________________________

          MRAMSGPNTR.OBJ       MIRA software module to be
                               linked with user applications.
                               It contains all the statuses
                               returned by the MIRA Application
                               Interface. (refer to MIRA User's
                               Guide)

          [MIRA_ADALIB...]     Ada objects and ACU files
                               necessary to compile an user
                               application program written in
                               Ada with the two packages MIRA
                               and MIRA_STATUS (if MIRA-Ada
                               required)

          UTDEF.ADA            Symbols and statuses used by the
                               MIRA Driver. for Ada programs (if
                               MIRA-Ada required)






















          B-6

 

                  List of the files provided by MIRA installation



          _______________________________________________________
          Directory:_SYS$TEST____________________________________

          MRA$IVP.COM          MIRA Installation Verification
                               Procedure
          MRA$DRVTEST.COM      Driver Tester command file

          MRA$DRVRESULT.DAT    Driver Tester expected results

          MRA$OITEST.COM       Operator Interface test command
                               file

          MRA$OIRESULT.DAT     Operator Interface test expected
                               results

          MRA$AITEST.COM       Application Interface Tester
                               command file

          MRA$AIRESULT.DAT     Application Interface Tester
                               expected results

          MRA$ADA_IVP.COM      MIRA-Ada Installation
                               Verification Procedure if MIRA-
                               Ada required

          MRA$ADA_             MIRA-Ada Interface Tester
          AIRESULT.DAT         expected results if MIRA-Ada
                               required














                                                              B-7
